AGM Industries - TACTOO Anchor Adhesive

Spec. Sheet GPA-72

TACTOO® GPA-72
Anchor Adhesive

ASTM E84
Surface Burning Characteristics
APPLIED TO INORGANIC REINFORCED CEMENT BOARD
FLAME SPREAD...................................0
SMOKE DEVELOPED...........................<5
Rated NFPA Class 1 or A

SPECIAL CHARACTERISTICS:
*Non-slip formula
*Performs in temperatures up to 250°F
*Immediate grab
*Provides excellent water/mildew resistance

DESCRIPTION:
TACTOO® GPA-72 is a high-strength, heavy-bodied, neoprene rubber adhesive, specifically formulated for adhering anchors for hanging insulation. GPA-72 is also recommended for use as a general purpose construction adhesive in applications requiring a high-strength bond or in applications subjected to high temperatures.

USES:
TACTOO® GPA-72 bonds metal and nylon anchors to metal, concrete or masonry surfaces. Also recommended for installing metal or ceramic wall fixtures in tile applications.

SURFACE PREPARATION:
Surfaces should be clean, dry and free of oil, grease, frost or any other foreign matter that will impair adhesion. Do not use over painted surfaces. Many protective coatings are not compatible with TACTOO® GPA-72. Clean all metal surfaces with 1,1,1, Trichloroethane, Acetone or other degreaser, exercising safe practices as recommended by the manufacturer.

APPLICATION:
Do not apply at temperatures below 30°F. Prepare and install one anchor at a time. Apply a dab (the size of a small walnut) of GPA-72 to the anchor base with a putty knife and immediately press anchor in place with a slight twisting motion (max. open time is 10 minutes). For proper adhesion, insure that the film of adhesive covering the anchor base (after the anchor has been firmly pressed into place) is protruding through the perforated base plate. Application will be dry within approximately 24 - 72 hours, depending on atmospheric conditions. Do not apply load until application is completely dry.

RECOMMENDATION:
When installing metal or ceramic wall fixtures or tile, butter the back with GPA-72 and immediately press in place with a slight twisting motion. Allow 24 - 72 hours before subjecting to use.

Store adhesive at room temperature for at least 24 hours prior to use. This product is manufactured by TACC International Corporation, formerly Miracle Adhesives.

See Material Safety Data Sheet (pdf)

TYPICAL PHYSICAL PROPERTIES AND TECHNICAL INFORMATION

BASE: Neoprene	FLAMMABILITY (wet stage): Extremely Flammable
SOLVENT: Toluene	FLASH POINT: 45°F (ASTM D 3278)
COLOR: Dark Green	WATER RESISTANCE: Excellent
CONSISTENCY: Heavy Mastic DO NOT THIN	MILDEW RESISTANCE: Resists fungus growth
SOLIDS CONTENT: 38% by weight	SERVICE TEMPERATURE: -30°f to 250°F
WEIGHT/GALLON: 8.2lbs.	APPLICATION TEMPERATURE: 30°F to 120°F
OPEN TIME: 10 minutes	STORAGE: Room temperature w/cross Ventilation. OSHA Class 1B Liquid. Store as per 29 CFR 1910.106
DRY TIME: 48 hours	SHELF LIFE: 12 months
COVERAGE: 500 - 1000 anchors/gal	CLEAN-UP: Toluene, exercising safe practices.
THERMAL SHOCK RESISTANCE: Excellent

WARNING !
FLAMMABLE LIQUID AND VAPOR
VAPOR HARMFUL.

CONTAINS: Toluene
Vapor harmful. May affect the brain or nervous system causing dizziness, headache or nausea. Causes eye, skin, nose and throat irritation.

NOTICE:
Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the content may be harmful or fatal.

PRECAUTIONARY MEASURES:
KEEP AWAY FROM HEAT, SPARKS AND FLAME. Vapors may cause a flash fire. Prior to use and until all vapors (odors) are gone: DO NOT smoke; DO NOT use electric switches; DO NOT generate static sparks: EXTINGUISH all flames and pilot lights and TURN OFF all electric and gas appliances, motors and other sources of ignition in work site, nearby rooms and lower floors. Vapors are heavier than air and may travel to such areas. PREVENT build-up of vapors by opening all windows and doors to achieve cross ventilation.

USE ONLY WITH ADEQUATE VENTILATION:
To avoid breathing vapors, open windows and doors or use other means to ensure fresh air during application and drying. If you experience eye watering, headaches or dizziness, increase fresh air or wear respiratory protection (NIOSH/MSHA TC23C or equivalent) or leave area. AVOID contact with eyes and skin. DO NOT take internally.

STORAGE/HANDLING:
Keep container closed when not removing adhesive. Do not reuse container or transfer adhesive to any other container.

FIRST AID:
Inhalation Overexposure - If dizziness or nausea occurs, remove person to fresh air and seek medical attention. Swallowing - If swallowed, call Poison Control Center, Hospital Emergency Room or physician immediately. Get medical attention immediately. Skin contact - Wash skin thoroughly with warm water and soap.

FOLLOW ALL PRECAUTIONS IN THE WORK AREA AND ALL ADJACENT AREAS. BE SURE THAT ALL PERSONS UNDERSTAND AND FOLLOW ALL PRECAUTIONS. KEEP OUT OF THE REACH OF CHILDREN.